SIMATIC ET 200S is the distributed I/O station that guarantees lasting savings in life-cycle costs with the highest flexibility. Installation couldn't be easier and the bit-modular design of the ET 200S enables multifunctional use of the station. 

This provides you with the following lasting benefits: Especially high savings in wiring (up to 80%) thanks to integrated technologies Significant space savings in the control cabinet (up to 50%) thanks to compact design Huge increases in availability due to "fixed wiring" Bit-modular design: up to 64 modules per station Powerful, self-buildup 40-A energy bus

Distributed I/O

Motor starters for all applications up to Category 4:
These fully pre-wired units can even be replaced during operation and under power. You can choose between the standard motor starter (up to 5.5 kW) and the high feature motor starter (up to 7.5 kW).

Distributed intelligence:
The integral CPU with the functionalities of the S7-300 enables advance startup, enhanced availability, and modular machine design.

Technology modules extend the possible applications:
Technology modules are intelligent modules that operate independently of the CPU and carry out the technological task largely autonomously. Parameterization of the modules is supported with STEP 7.

There are modules for the following applications: High-speed counting Position decoding with SSI encoders Positioning with pulse/direction interface Controlled positioning in rapid traverse/creep speed procedure Control of actuators for proportioning, adjustment, closed-loop control

Distributed CPU's

Integration of safety technology with SIGUARD or PROFIsafe:
PROFIsafe components support the reading in, processing and output of safety data through PROFIBUS DP in the same way as standard data. This enables "safe" and "unsafe" modules to be included in a mixed configuration and their data to be exchanged with the PLC over a common PROFIBUS DP bus line. PROFIsafe provides safety to Category 4 of EN 954-1.

Fine-modular distributed I/O system with IP 20 degree of protection is suitable for operation in hazardous zone 1.

Take the control cabinet out of your equation and effectively reduce the costs of your plant with SIMATIC ET 200X. Our control-cabinet-free I/O with high degree of protection IP65/67 (NEMA 4) and rugged plastic housing can be flexibly expanded with up to 7 modules of the most varied functionality.

SIMATIC ET 200L is the I/O station in postcard format with degree of protection IP20. It is used predominantly in the low-end performance range with few inputs/outputs. It is also ideal where space is restricted. In addition, it is characterized by an optimized price-performance ratio.

The compact ET 200L I/O station comprises a terminal and an electronics module. It is connected to the Profibus-DP fieldbus using the interface integrated into the electronics module. The ET 200L is a slave on Profibus-DP with data transfer rates up to 1.5 Mbit/s.

Two versions of the ET 200L are available: As block I/O: not expandable As modular I/O: expandable with SIMATIC Smart Connect (ET 200L-SC)

SIMATIC ET 200M is the modular I/O station for the control cabinet with high density-channel applications. The signal modules, communications processors and function modules of the SIMATIC S7-300 can be used. The Ex-analog HART input and output modules mean that the ET 200M is ideal for use in process engineering. Can also be used in connection with redundant systems (e.g. S7-400H). The maximum data transfer rate is 12 Mbit/s.

Their performance range encompasses the following features: Extensive range of the most varied electronics modules The safety-related modules comply with PROFIsafe specifications and enable new, simple safety concepts Special Ex analog modules are suitable for use in process engineering Active modules allow module replacement during operation (hot-swapping) High availability thanks to redundant design Also available with integral fiber optic interface for plastic and PCF cables Condensation-resistant modules for the temperature range -25 to +60°C Can be used as DPV1 slave Time stamping of digital input signals

This cost-efficient digital block I/O enables cabinetless installation with IP67 protection right at the site of the process. Eco stands for "easy connection, easy commissioning and economical". Two connection systems are available: M12 and Ecofast.

The following features are typical of the new I/O: Compact, rugged, easy-care housing T functionality: the electronic block permits hot swapping without interrupting the power supply or the bus line

Variable and flexible connection blocks are available for:

• ECOFAST: 2x hybrid fieldbus RS485 interface module with identification plug for setting the PROFIBUS address
• M12: 2x M12 and 2x 7/8" with 2 rotary coding switches for PROFIBUS address assignment
• Module versions: 8DI, 16DI, 8DI/8DO (1,3A), 8DI8DO (2,0A), 8DO, 16DO
• Connection capability for non-equivalency sensors on the 16DI version
• Module diagnostics for load voltage and sensor short circuit
• Interface to Profibus-DP with transmission rates of up to 12 Mbit/s

Module variants:

• 8 DI, 16 DI, 8 DI/DO (1.3 A), 8DI/8DO (2.0 A), 8DO, 16DO

The new ET200R is Distributed I/O to the IP65 degree of protection.

Cast aluminum housing with Integrated repeater.

Parameterizable inputs/ outputs: 8 DI/8 DO up to 16 DI. Push-on terminal strip for connecting analog signals for welding transformers. Connection to 17-pin M23 connector via hybrid cable

The Actuator-Sensor Interface (ASI) is a standardized non-proprietary networking system for the connection of sensors, actuators and other control equipment at the lowest field level.

Many system components are available to implement communications.

The basic components of a system installation are:

Master interfaces for central control units such as SIMATIC S5 and SIMATIC S7, distributed I/Os ET 200 ® M/X AS-Interface shaped cable Network components such as repeaters/extenders Power supply unit for powering the slaves Modules for connecting standard sensors/actuators Actuators and sensors with integrated ASIC slave Fail-safe modules for transmission of secure data through AS-Interface Address programming device for setting the slave address

The MVK family with IP67 protection was conceived specifically for heavy duty applications in a mechanical environment. The modules can be installed close to the sensors and actuators, this keeps the cable connections short and additional enclosures are not required.

The extensive use of LEDs on the module and over the field bus to the master facilitates commissioning of the system and fault location. All outputs and sensor supplies are short circuit and overload protected. All inputs and outputs are electrically isolated from the field bus. The separate voltage connection from the bus interface and the I/O sector, enables an alarm output to be available.

The demands placed on products in the field these days are often extreme. Aside from a of IP67 rating or better, requirements are increasingly for high vibration and shock resistance, but also for water proofing.

MVK Metal is available for Profibus DP and DeviceNet. In addition to an input module with Pin 2 diagnosis, it also has a freely parameterizable module, in which each channel can be configured individually as an input or an output, and that for both Pin 4 and Pin 2 of the socket.

Cube67 is the most innovative IP67 protection I/O system for the most common field bus systems. The innovation is seen partly in a distributed, modular concept, partly in the new technologies such as multifunctional I/Os and the comprehensive diagnosis functionality.

Multifunctional I/Os, and the free parameterization of the plug positions, whether input, output or debugging input, give a maximum of flexibility. You can choose which plug position you need for an input or output, for 2 signals per M12 socket. Separate modules for inputs and outputs are no longer needed.

The simple insulation-displacement connection of the flat cable speeds up the installation of the bus and supply cables.

• Modules available with M8 and M12 Ports
• Available in 4 Port and 8 Port Boxes for use with Digital Inputs and Outputs

Other available ASI System Components:

Master for PC's Gateways ASI power supply unit Addressing device Repeaters Connectors Valve Connectors

The Systron ® RIO Compact I/O system is excellent for small spaces and expandable when I/O requirements grow with either full expansion modules of 16I/O for larger expansion or with the extension box facilitating as little as 4 I/O for smaller expansion.

Supported fieldbuses include Profibus, Interbus, DeviceNet, CANopen, WorldFIP & Ethernet TCP/IP. All I/Os are UL listed, CSA certified, rated Class 1, Div. 2, and CE marked.

The Systron ® PM Flexible I/O System is modular and allows you to build the I/O station that fits your application.

Supported fieldbuses include Profibus, Interbus, DeviceNet, CANopen, Modbus, and the Schiele E/A-bus. Digital I/O Analog I/O including Thermocouple & RTD Special Modules such as High Speed Counters, Linear Positioning, Potentiometer, Passive Terminal Block and Stepper Motor Controller Modules All I/Os are UL listed, CSA certified, rated Class 1, Div. 2, and CE marked

• I/O Modular Stations
• Remote Fieldbus I/O
• Distributed I/O Systems
  
  Smaller, faster, more flexible and more economical – these are the trends in automation. Phoenix Contact actively pursues these trends with innovative I/O systems for perfect cabinet building and field wiring solutions.