Distributed by Ontor Limited: Siemens new SIRIUS 3RW40 soft starters in the lower power range from 10-75HP @ 600V expand the performance spectrum of the 3RW40 soft starters. They represent a very compact and price-attractive alternative to start-delta starters. Siemens' comprehensive range of SIRIUS soft-starters will reduce the inrush current and mechanical stress that usually occurs during standard direct on line starting of AC motors. Siemens' innovative, high quality technology will smoothly start and stop your motor, reduce the In-rush current and mechanical stress while protecting the motor against overload conditions.

With the new 3RW40 line, customers can take advantage of many benefits of additional NEW features such as built-in Overload Relay, Voltage Control and Current limiting technology, Integrated remote reset (without additional module), programmable ON/RUN output and fault output, and Polarity balance just to name a few.

Ontor Limited is a national distributor of Industrial Controls and Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Cambridge, Mississauga and Edmonton.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2008-04-11

FOR IMMEDIATE RELEASE:

Mini-VersaTRAK mIPm PLUS

The Ultimate Truly Open Enhanced RTU for Utility Industry Applications SIXNET's latest addition to their IPm product line is the Mini-VersaTRAK mIPm PLUS RTU. The mIPm+ (which stands for mini-IPm PLUS) is a compact unit with Ethernet, up to 4 serial ports and a built-in mix of 26 discrete and analog I/O. Like all of SIXNET's IPm Controllers and RTUs it is pre-loaded with open-source Linux and the IPm firmware which offers many advanced automation, control and data acquisition capabilities. The mIPm+ can be programmed using any mix of the ISaGRAF IEC61131-3 languages (ladder logic, sequential function chart, etc.).

In addition to all of these standard features, this special edition mIPm+ includes an abundance of memory and pre-loaded software for AGA gas flow calculations and DNP-3 time stamped communications with the needs of the utility industries in mind.

Inside the mIPm+, there is 64 Mb of flash disk and 32 Mb of fast dynamic memory, along with a 32 bit industrial PowerPC. The mIPm+ also offers a unique hot swap capability which minimizes downtime and makes it easier to keep a system running smoothly. The mIPm+ is UL/CSA/CE rated for -40 to +70°C operation, Class 1, Div. 2 (Zone 2) hazardous locations and marine/offshore applications.

Steve Schoenberg, CEO, states, "The mIPm+ is a complete RTU system that fits in the palm of your hand – the utility industries’ dream come true. It includes all of our powerful firmware, loaded with industrial automation features that are ready to use right out of the box. Plus, the open-source Linux makes it truly open and allows for ultimate flexibility. The new inclusions of AGA and DNP-3 make mIPm+ the ideal choice, in a compact footprint. Simply stated, it will make your job easier."

The mIPm+ can be programmed using any mix of the ISaGRAF IEC61131-3 languages (ladder logic, sequential function chart, etc.), high-level C/C++ and more. OEMs can even add their own applications, making the mIPm the perfect OEM product platform. It also offers many advanced features that do not require any programming. For example, with the supplied SIXNET I/O Tool Kit software users can configure datalogging and I/O transfer routines to occur periodically or on an event such as an alarm. This configuration software also allows users to import/export tag definitions, load custom programs, perform diagnostics and much more.

New in the mIPm+, additional memory capacity has allowed for inclusion of bundled software applications, without affecting performance, at no extra cost. The AGA gas flow calculations include AGA-3 (orifice plate), AGA-7 (turbine meter), AGA-8 (gas density), Accelabar from Veris and comply with the Chinese SY/6143-2004 standard. The addition of DNP-3 communications, the utility industry standard for time stamping events and verifying occurrence of required actions, provides a fully featured DNP-3 slave that is included to connect to any compliant DNP-3 master over a serial, wireless, or Ethernet link. Both applications software packages are easily configurable through the SIXNET I/O Tool Kit and run seamlessly with all other SIXNET IPm applications including ISaGRAF, SIXNET’s Sixlog, and ALL IPm I/O drivers.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2008-04-11

FOR IMMEDIATE RELEASE:

Ontor Limited hits its 60th Anniversary

Ontor Limited is excited to announce that in 2008, it has reached a major milestone, its 60th anniversary.    Ontor is a privately owned, family business that was incorporated in 1948 by the father and son team of Charles and John Elder.   John’s son, Robert is now President of the company and continues the tradition of growth and customer focused excellence.

Initially, Ontor earned business through word of mouth, so it had to ensure the very best in quality products and customer service in order to become a trusted supplier. A lot has changed over the years, but these same values are still at the core of Ontor’s business today.   Ontor’s management team realizes that another key to success is keeping abreast of industry issues and for this reason, Ontor is an active member of numerous industry associations including: COHA, HRAI, NHRAW and RSES to name a few. Ontor prides itself on seeking new ways to adapt its products and services to meet the needs of its customers.    Ontor is committed to growing along with its Canadian customer base. “The Canadian market is full of new opportunities for Ontor” said President Robert Elder. “We are constantly looking for ways to become even better at serving our customers.”

Two components that have contributed to Ontor's success are the fact that Ontor maintains its status as One of ‘Canada’s 50 Best Managed Companies’. This means that Ontor has been recognized as a company, which has consistently maintained success and achievement at the highest level.   The second factor is that Ontor is ISO 9001-2000 Certified.   “Becoming ISO certified has allowed us to increase our business due to potential clients who strictly dealt with ISO certified companies. Good quality systems improve efficiency and open up market opportunities. The ISO program served to streamline processes and procedures providing accountability and consistency throughout the quality system. In order to ensure that product quality continues to meet or exceed customers’ expectations,” according to Robert Elder company president.

Ontor’s head office is located in Toronto, ON and there are regional offices across Canada in Montreal, Vancouver, Halifax, Edmonton and Winnipeg, Burlington, Mississauga, Cambridge and Quebec City. Consisting of two business sectors HVAC and ISD (Industrial Automation Systems Division), Ontor employs about 85 people nationally.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2008-03-05

FOR IMMEDIATE RELEASE:

Ontor Limited Appoints New Branch Managers

Ontor Limited is pleased to announce two new Managers in our Toronto and Burlington offices. Terrence Francis has been promoted to Regional Manager for the Toronto corporate branch. Terrence has over eighteen years of experience in the industrial electrical distribution business and has spent the last three years at Ontor working as part of the Automation Team. He came to us with a well rounded controls and automation background. He is looking forward to the challenges accompanying his new position.
In our Burlington office, Angelo Sanfilippo has been promoted to the position of Branch Manager. Angelo was previously working out of the Cambridge office as our Motion Controls Specialist . Angelo’s new role will comprise of focusing on corporate strategy and new business development for our complete offering including Motion Control.

Ontor Limited is a national distributor of Industrial Controls and Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Cambridge, Mississauga, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2007-01-29

FOR IMMEDIATE RELEASE:

Ontor Acquires RoMark Technologies Corporation

Ontor Limited is excited to announce that as a result of the acquisition of RoMark Technologies Corporation we have been appointed the exclusive Canadian representatives for several exciting product lines. The first of these lines is Beta LaserMike specializing in Precision Measurement and Control Systems for the Plastics, Automotive and Metals industries. Other product lines that Ontor will be representing include: Z-Mike – dimensional metrology systems, American Kuhne – plastic and rubber extruders as well as complete extrusion lines, Colortronic – plastic processing equipment, Genca – extrusion crossheads, in-line heads and tooling, Pixargus – automated surface inspection and profile measurement systems for rubber and plastic extrusion, Clinton Instrument Company – pinhole (leak) detection systems and spark testers for continuous monitoring for product quality, Metrilogic – special measurement, data collection and management information software. Finally, Ontor is the new representative for AW Machinery who manufactures electrical wire and cable equipment.

Ontor’s new product lines have been attained in our efforts to supply our customer quality, leading edge technology, strong technical sales, and application support with local service.

RoMark products can be viewed at www.romark.ca

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2007-01-01

FOR IMMEDIATE RELEASE:

Ontor Limited does it again!!

We are 'One of Canada's 50 Best Managed Companies"

Ontor Limited has requalified to maintain its status as one of ‘Canada’s 50 Best Managed Companies. This means that Ontor has been recognized as a company which has consistently maintained success and achievement at the highest level. Ontor is a National Distributor of HVAC Components/ Industrial Automation Systems. The corporate office is located in Toronto with regional offices across Canada.

“Achieving the highest level of business performance over the long-term is only possible when organizations embrace a culture of aligning every activity and resource with building value for their stakeholders,” said Deloitte Partner with the Private Company Services Group, and National Leader of the Best Managed program, John Hughes. “Membership in these groups symbolizes the ultimate goal for any business – sustained high performance. All companies strive for business success; what distinguishes Platinum Club and Requalified members is their ability to sustain that success.”
“The success of these companies – the best of the best – is an inspiration to all Canadian businesses,” said James McSherry, Executive Vice President and Managing Director, CIBC Commercial Banking. “Sustaining the highest level of business performance over the long-term is fraught with challenges. Only the fittest succeed in making the giant leap from small entrepreneurial operations to multi-million dollar enterprises, avoiding the many pitfalls along the way.”
Practices that have made Ontor a winner include state of the art business and logistical systems to enhance operational excellence; key measurement indicators which calibrate their position against the best, representation of only world class suppliers and employee incentive plans to motivate and reward.

Robert Elder the company’s President comments, “ This is a true high point in our firms rich 59 year history. It is an accomplishment that all of our talented staff should be very proud of. They made us successful, each and every one’s individual contribution has always allowed our firm to grow and prosper. We also are grateful to our world-class suppliers for providing us with the products that have enabled us to grow. Of course without our loyal customers continued belief in our total solution sales approach this could not have happened!”

Established in 1993, Canada's 50 Best Managed Companies (Best Managed) is one of the country’s leading business awards program, recognizing excellence in Canadian-owned and managed companies with revenues over $10 million. Every year, hundreds of entrepreneurial companies compete for this designation in a rigorous and independent process that evaluates the caliber of their management abilities and practices. The awards are granted on three levels: 1) Best Managed winner (one of the 50 new winners selected each year), 2) Requalified member (repeat winners retain the Best Managed designation for two additional years, subject to annual operational and financial review), 3) Platinum Club member (winners that maintain Best Managed status for a minimum of six consecutive years.) Program sponsors are Deloitte, CIBC Commercial Banking, National Post, and Queen's School of Business.

The 50 new 2006 Best Managed winners will be announced on February 7, 2007. A one-day Symposium and Gala event for Best Managed Companies follows on February 12, 2007 in Toronto. This Symposium will provide an opportunity for executives to exchange ideas and gain new management and leadership insights from their peers and keynote speakers. At a black-tie Gala that evening, Best Managed Companies will celebrate their success with their executive management teams and fellow honourees.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-10-11

FOR IMMEDIATE RELEASE:

Ontor takes on New Lines in Quebec

Ontor Limited (in the Quebec Regions) is excited to announce that we have been appointed the distributor for several new product lines. The first of these lines is Eaton Cutler-Hammer. Eaton is a business leader in electrical controls, power distribution, uninterruptible power systems and industrial automation products and services. Products that Ontor will be distributing include XT controls, Push buttons & Pilot Lights, Sensors, PanelMate, ELC PLC, Drives and their intelligent MCC.

The second of Ontors new lines is Phoenix Contact. Phoenix Contact offers an innovative portfolio of industrial electro-technology. The best connections "from the sensor to the controller." From the classical modular terminal blocks to splash-proof machine connectors to the wireless Ethernet: Innovations, which do more than customers expect.

Finally Ontor is the new representative for Toshiba. Toshiba’s Industrial Division is a world leader in the design and manufacture of motors and variable Frequency Drives products.

Ontor’s new product lines have been attained in our efforts to supply our customer quality, leading edge technology, strong technical sales, and application support with local stock and service.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-07-27

FOR IMMEDIATE RELEASE:

SERIAL TO FIELDBUS AND INDUSTRIAL GATEWAY FAMILY WITH AN EASY 6 STEP NETWORK SETUP. IDEAL FOR FACTORY, BUILDING AND PROCESS AUTOMATION INDUSTRIES

Ontor is pleased to announce that we are a distributor for the ANYBUS Communicator. The main feature that makes this communicator ideal is that it is ideal to connect devices with serial interfaces to all major industrial networks. Key features include RS232/422/485 selection possible with Config Tool; Max 512 bytes of Input data and 512 bytes of Output data; Supports Modbus RTU Master, Generic data and ASCII; Baud rate on the serial interface selectable between 9,6 kbit/s and 57,6 kbit/s; Multi-drop up to 31 nodes; Line Listener to analyze serial telegrams on the sub-network; Password protection prevents unauthorized upload and download of configurations; ConfigTool and Wizard for easy config and serial sub-network setup; Multi language support, now supporting English, German, Italian and French, Swedish, Chinese.
The Anybus products give Manufacturers, OEMs, System Integrators and users a flexible, economical and reliable solutions to exchange data with devices and systems on the plant floor. Modem communication technologies such as Profibus, DeviceNet, Modbus, EtherNet/IP, CC-Link, ControlNet, CANopen, Interbus, Profinet, Lonworks, AS-Interface, FIPIO, USB and Bluetooth are all supported by Anybus.
Ontor is a national distributor of Industrial Controls and Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-05-01

FOR IMMEDIATE RELEASE:

Ontor Limited Introduces New Sales Counter

Ontor is pleased to announce that our head office in Toronto located at 12 Leswyn Road, near Yorkdale Shopping Mall, has recently opened a Sales/Pickup counter. This new sales counter will be open from Monday to Friday, 8am to 5pm and staffed with friendly and technically knowledgeable sales people. We will now be able to better serve and support our customers with immediate access to our broad inventory. Ontor is the exclusive industrial distributor for Siemens Industrial Controls, Drives, Safety and Automation products as well as many other industry leading name brand product lines including BEL enclosures, Edison fuses, Transfab transformers, Baumer sensors and more. Ontor supports several methods of payment such as cash, debit, Visa, Mastercard, or apply for credit if you don't already have an account with us.
Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-05-01

FOR IMMEDIATE RELEASE:

SOLID-STATE SAFETY COMBINATIONS AND LOAD FEEDERS

Distributed by Ontor Limited. Siemens integrated safety technology package includes the safe load feeder which unites the advantages of solid-state safety technology with the benefits of the SIRIUS 3R modular system. This combination of one motor starter protector and two series-connected contactors provides a complete, preassembled, wired and certified safe load feeder, either type of coordination 2 or weld-free. Depending on its design, this load feeder complies with EN 954-1 Category 3 or 4.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Waterloo, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-04-19

FOR IMMEDIATE RELEASE:

Ontor Appointed Distributor for Bel

Ontor Limited has been appointed the distributor for BEL Products. BEL provides an extensive range of enclosures covering most electrical protection and distribution needs. With the latest 3-D design and NC programming techniques, highly automated and robotized production equipment, BEL offers a wide range of superior built enclosures. Whether the need be for TYPE 1 dust & contact prevention, TYPE 4 watertight protection or TYPE 4X higher corrosion resistance applications, whether steel, stainless steel, aluminum, galvanized steel, PVC or polyester is required.

Since 1964, Bel Products Inc. has provided electrical wholesalers and contractors with top quality electrical and electronic enclosures and accessories at the most competitive prices, shortest delivery time and qualified after sales services.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-04-01

FOR IMMEDIATE RELEASE:

ASI SAFETY AT WORK

Distributed by Ontor Limited. Siemens Safety at Work concept supports the direct integration of safety-related components, such as EMERGENCY STOP switches, protective door switches or safety light arrays, in the AS-Interface network. These are fully compatible with the familiar AS-Interface components (masters, slaves, power supply units, etc.) in accordance with EN 50295 and are operated in conjunction with them on the yellow AS-Interface cable.
The signals of the safety sensors are evaluated by a safety monitor. The safety monitor does not only monitor the switching signals of the safety sensors, but also continuously checks whether the data transmission is functioning properly. The safety monitor has two two-channel release circuits which are used to put the machine or plant into a safe state. The sensors and monitor can be connected to any point of the AS-Interface network. It is also possible to use several monitors on a single network.
A failsafe control or special master are not required. The master treats safety slaves like all other slaves and receives the safety data for information only. In this way, all existing AS-Interface networks can also be expanded.
Safety at Work ensures that a maximum response time of 40 ms is achieved. This is the period between shutting down the output on the safety monitor and applying the signal on the input of the safe slave.
The system has been tested and approved by TÜV (German Technical Inspectorate). The transmission procedure for safety-related signals has been designed so that applications up to Category 4 can be implemented acc. to EN 954-1, or SIL 3 acc. to IEC 61 508.
The configuration SW can be used to compile the safety-related applications and transmit them to the monitor. The software also allows online diagnostics.
Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-04-01

FOR IMMEDIATE RELEASE:

SIEMENS FAILSAFE LIGHTCURTAINS

Distributed by Ontor Limited. Siemens contactless, active optoelectronic light curtains and grids
for Categories 2 and 4 according to EN 954-1 and type 2 or 4 in accordance with IEC/EN 61496 protect operators at or near machines and systems in operation. Thanks to specially developed integrated circuits (ASICs) and a patented, intelligent analysis process, they are especially failsafe and highly available. Whether protecting body parts, securing horizontal hazardous areas or the access to larger areas - the widest range of functions such as start and restart locking, contactor monitoring, jog control or blanking allow for many different applications. A version for connecting to the AS-Interface is available. A light curtain or light grid comprises a transmitter and a receiver, which must be mounted opposite each other. Depending on the resolution and the length, a certain number of transmit and receive diodes are arranged vertically. The infrared LEDs of the transmitter emit short light pulses that are detected by the receive diodes.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-04-01

FOR IMMEDIATE RELEASE:

SIEMENS SAFEY CONTROL SYSTEMS

Distributed by Ontor Limited. Siemens Safety systems provide the highest level of safety for humans, machines and environ¬ment. They are used to prevent accidents and damage resulting from a fault or mal¬function. The safety SIMATIC controllers (SIMATIC Safety Integrated) monitor themselves, detect faults autonomously and immediately change into or remain in a safe mode when a fault occurs. They are optimized for use in production engineering and provide air-tight safety for all its many facets.

Ontor Limited’s corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-03-06

FOR IMMEDIATE RELEASE:

PROCLIP SYSTEMS

Distributed by Ontor Limited is the Proclip system by Bel Products. The Proclip is an intelligent modular way to organize your electrical enclosure.
The basic idea is quote simple: assemble electrical panel frames using an innovative modular "snap in" system, entirely eliminating the need for labour-intensive operations such as tracing, cutting, drilling or tapping. This patented system simplifies wiring, maximizes space and offers a range of concrete advantages that will generate savings at each stage of production. Proclip increases overall efficiency by reducing the size of your enclosure upto 50% and reducing the assembly and wiring time by upto 30%. The Proclip system also offers optimal accessibility because all of the components clearly stand out which allows easy access to your control points.
Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-02-03

FOR IMMEDIATE RELEASE:

ONTOR NAMED ONE OF CANADA'S

50 BEST MANAGED COMPANIES

Ontor Limited was chosen over thousands of other applicants to win a 2005 Canada’s 50 Best Managed Companies award. This prestigious national award is sponsored by Deloitte, CIBC Commercial Banking, National Post, and Queen’s School of Business. Ontor is a National Distributor of HVAC Components/ Industrial Automation Systems. The corporate office is located in Toronto with regional offices across Canada.

“The 2005 Best Managed winners are an outstanding group of Canadian-owned and managed companies that have proven their remarkable ability and commitment to apply best practices to all areas of their business operations,” explained Tony Grnak, Deloitte partner and National Leader, Canada’s Best Managed. “These companies clearly demonstrate innovation, leadership and a laser focus on their customers and employees. Their example illustrates that focusing on business fundamentals while pursuing a clearly defined strategy is key to achieving exceptional results.”

Practices that have made Ontor a winner include state of the art business and logistical systems to enhance operational excellence; key measurement indicators which calibrate their position against the best, representation of only world class suppliers and employee incentive plans to motivate and reward.

Established in 1993, the Best Managed award is a national program, recognizing Canadian companies that have implemented world-class business practices and created value in innovative ways. Applications are reviewed by an independent judging panel that evaluates how companies address various business challenges, including new technologies, globalization, brand management, leadership, leveraging and developing core competencies, designing information systems, and hiring the right talent to facilitate growth.

Robert Elder the company’s President comments, “ This is a true high point in our firms rich 58 year history. It is an accomplishment that all of our talented staff should be very proud of. They made us successful, each and every one’s individual contribution has always allowed our firm to grow and prosper. We also are grateful to our world-class suppliers for providing us with the products that have enabled us to grow. Of course without our loyal customers continued belief in our total solution sales approach this could not have happened!”

“Out of thousands of applications and a grueling vetting process, Ontor Limited emerged as one of Canada’s 50 Best Managed Companies,” enthused James McSherry, Executive Vice President and Managing Director, CIBC Commercial Banking, a national sponsor of the program. “This company is inspiring on every level – you can see their dedication to their customers base continually striving for total satisfaction.”

2005 winners of the Canada’s 50 Best Managed Companies award, along with Requalified winners, and Platinum Club members will be honored at the annual Best Managed gala in Toronto on 6 February, 2006. On the same date, the Best Managed symposium will address leading-edge business issues that are key to the success of today’s business leaders.

About Canada’s Best Managed Companies
Established in 1993, Canada's 50 Best Managed Companies (Best Managed) is the country’s leading business awards program, recognizing excellence in Canadian-owned and managed companies with revenues over $10 million. Every year, hundreds of entrepreneurial companies compete for this designation in a rigorous and independent process that evaluates the caliber of their management abilities and practices. The awards are granted on three levels: 1) Best Managed winner (one of the 50 new winners selected each year), 2) Requalified member (repeat winners retain the Best Managed designation for two additional years, subject to annual operational and financial review), 3) Platinum Club member (winners that have maintained Best Managed status for a minimum of six consecutive years.) Program sponsors are Deloitte, CIBC Commercial Banking, National Post, and Queen's School of Business. For further information, visit www.canadas50best.com

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2006-02-01

FOR IMMEDIATE RELEASE:

Typical Problems, Superior Solutions with HG7 Filters

Non-linear Loads and the Impure Sine Wave
Non-linear loads are products that draw non-sinusoidal current from the distribution line. This nonsinusoidal current is derived from waveforms that combine the fundamental frequency with integral
multiples of that frequency. The resulting harmonic distortion is a basic result of the operation of nonlinear
loads. When these types of loads are a significant portion of an electrical system, harmonic distortion
may begin to cause problems throughout the entire system. These problems range from poor power factor,
transformer and distribution equipment overheating, random breaker tripping, or even sensitive equipment
failure. Since harmonics affect the overall power distribution system, the power utility may even levy heavy fines when a facility is affecting the utility’s ability to efficiently supply power to all of its customers. As a result, in the search for more efficient power use, other costly issues have been created.
Superior HG7 Performance
The HG7 not only limits current distortion to less than 7% TDD, it also improves true power factor.
Multiple package options will allow TCI customers to choose the right filter configuration for the application.
Since every power system is different, harmonic mitigation requirements will differ, and even IEEE limits
change based on the system loading characteristics. The HG7 product returns the power of choice to
the customer, allowing for different configurations to achieve different performance and monitoring
results. It is TCI’s intention to provide the maximum value to our customers by offering the package and performance necessary for the application.

True Power Factor Correction
“Real” or True power is used to perform real work. Inductive loads require Real and Reactive power. Utilities provide Apparent power. Apparent power is a geometric combination of Real and Reactive (or imaginary) power. Reactive power performs no work. However, the flow of reactive current, a component of reactive power, does consume energy as it passes through resistive elements of the power system. Thus, reducing overall system efficiency. This reactive power is used to generate magnetic fields within motors, transformers, and other magnetic devices. Reactive power, combined with harmonic currents, contribute to poor power factor in electrical systems. The capacitors inherent in the HG7 design supply the necessary reactive power so the utility doesn’t have to. The reduction in harmonic currents further improves the ratio of active power to apparent power. This overall improvement to true power factor assists in the efficient operation of facilities and the avoidance of possible fines due to poor power factor.

IEEE-519 1992 Harmonic Distortion Limits
In 1981, “Recommended Practices and Requirements for Harmonic Control in Electric Power Systems” was published. This document was the first attempt at establishing acceptable standards for distortion, both voltage and current, within the distribution system. Unfortunately, the original document did not address the users’ responsibility for contributing to the overall system distortion levels. Re-published in 1992, IEEE 519 set forth distortion limits for power users. These limits defined the maximum current and voltage distortion percentages allowable at the point of common coupling, commonly referred to as the PCC, under full load. These limits
are on a sliding scale based on system loading parameters.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-12-01

FOR IMMEDIATE RELEASE:

Northern Ontario mine reduces energy costs by $750 000 annually

Distributed by Ontor Limited. In June 2005, KIDD Creek Mine in Timmins, Ontario started a new energy management initiative. Like most mines, the ventilation system at the nickel mine was known to provide a significant opportunity for energy reductions. Following an analysis of the ventilation system, it was determined that the main ventilation fans could be turned down by 50% for 23 hours a week.

The savings are achieved by reducing the volume of air at strategic times throughout the day. Twice daily, during shift changes, the ventilation system is turned down by fifty percent and ramped back up again when the workers begin operating.

The ventilation network is controlled by NRG-1; a web based energy management system. NRG-1 is produced by Bestech, a Sudbury-based engineering and software company. The implementation of the project took less than one month. Savings were realized immediately and continue to mount up.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-12-01

FOR IMMEDIATE RELEASE:

Itronix GoBook VR-1 Notebook

Distributed by Ontor Limited. Itronix’s GoBook VR-1 Notebook was designed to set a new standard for durability, performance and connectivity in the semi-rugged computing segment. Like other Itronix products, the GoBook VR-1 notebook features integrated wireless capabilities that provide powerful connectivity generally not available in commercial notebooks, to allow users full flexibility in connectivity options that include support for up to four concurrent radios: Wi-Fi, WWAN, GPS and Bluetooth. Built to withstand the vibration, temperature extremes, bumps, shocks, and spills that mobile computer users encounter daily, the Itronix semi-rugged GoBook VR-1 notebook was developed to appeal to both industrial users, as well mobile professionals that need a tough computer to reliably endure the tumultuous and often unpredictable conditions that come with using a notebook on the go. The GoBook VR-1 notebook meets tough military standard (MIL STD 810F) for vibration, humidity, and operating temperature range, and has outstanding shock and spill resistance

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-12-01

FOR IMMEDIATE RELEASE:

SIEMENS SIMOCODE

Distributed by Ontor Limited Siemens SIMOCODE pro is a flexible, modular motor management system for motors with constant speeds in the low-voltage performance range. It optimizes the connection between I&C and motor feeder, increases plant availability and allows significant savings to be made for startup, operation and maintenance of a system.
When SIMOCODE pro is installed in the low-voltage switchgear cabinet. It is the intelligent interface between the higher-level automation system and the motor feeder and includes the following:

Multifunctional, solid-state full motor protection for motor currents up to 820 amps, which is independent of the automation system.
Flexible software instead of hardware for the motor control
Detailed operational, service and diagnostics data
Open communication via PROFIBUS DP, the standard for fieldbus systems.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-10-01

FOR IMMEDIATE RELEASE:

Intrinsically Safe PDA i.roc x 10-Ex

Distributed by Ontor Limited. Light, ergonomic, ruggedized and SAFE- optimized for high productivity! The ecom i.roc x 10-Ex is a physically compact, high performance industrial PDA based on a Pocket PC. Integrated WLAN 802.11b, Bluetooth and IrDA infrared port. Three different versions of the i.roc x 10-Ex meet the diverse needs and requirements of industry for ex-areas or unclassified areas. Optional integrated Barcode Scanner or RFID Reader. Its ergonomic design facilitates fatigue free operation during continuous use. High-resolution colour display can be read under even the most unfavorable light conditions. Protection from static electricity, water and dust; shockproof housing (non-corroding).
Approved for:

Ex II 2G EEx ia IIC T4
I.S. Class I Div 1 A-D
N.I. Class I Div 2 A-D

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-10-01

FOR IMMEDIATE RELEASE:

Introducing The new Factory Vision™ Line of Full Color Marquees

and Process Control Boards

Distributed by Ontor Limited. Electro-Matics Products introduce the Factory Vision™ family of full color marquees and process control boards that gives you unprecedented flexibility not only with layouts, but now color as well. Specifically designed to integrate seamlessly with manufacturing intelligence and data collection systems, the board’s embedded Pentium PC processor allows for maximum throughput speed in combination with multiple input sources. In addition to easy integration into your factory’s communications system, these new marquees and process control boards offer 262,000 shades of red, green and blue colors including white making them ideal for any application.

This family of robust industrial displays has been developed to meet the needs of a variety of manufacturing applications. Factory Vision™ displays are capable of standard row-column layouts, multiple page full text and graphics, or full motion video replay. This is now enhanced with the addition of blue’s and white colors to handle all your specifications needs.

The Factory Vision™ bundled software includes utilities to streamline your integration and give you maximum connectivity options. FCV marquees and and on boards allow direct linking to a variety of PLC’s, plus communication via ethernet to server based systems such as Activplant™ (formally visualplant™), Wonderware™, Cimplicity™ & NETCON Technologies Marquee Manager™. In addition, the FCV family of display boards can communicate to numerous proprietary protocols such as Ford POSMON, GM Protocol, DaimlerChrysler FIS, etc.

The Factory Vision™ product line was designed with extremely low life cycle cost as a major design criteria. This has been achieved with premium LED’s, ultra efficient power handling and modular mechanical design. You can expect the FV family of products to provide exceptional ROI with high Mean Time Between Failure (MTBF) and very low Mean Time To Repair (MTTR) characteristics. Without sacrificing viewability, FV products keep your life cycle cost at a minimum with leading edge technology aimed at a minimum in energy consumption.

The Next Generation
Lean manufacturing and visual factory management represent the next generation of manufacturing. These systems rely on real-time information and feedback regarding the status of the plant to achieve success. Marquees, andons, industrial clocks and counters, and process control boards provide the perfect answer to this growing demand. They open a window to factory performance and supply the foundation for a company-wide “nervous system”, ensuring all employees understand how they affect the overall performance of the factory.

Electro-Matic assembles and markets, under license with MacDonald Humfrey Products,
Inc. the next generation of marquees, andons and process control boards—Factory Vision™. The Factory Vision™ line is an industry-recognized leader in meeting the needs of companies adopting lean manufacturing and visual factory management.

Scott Beaver, Ford Account Manager for Electro-Matic Products, Inc., says “Our Factory Vision line is the perfect answer to all my customer’s visual factory management needs. They continually tell me how easily the displays integrate with their existing software and how well the displays improve productivity and their bottom line. And, the need for this product continues to grow as more and more companies adopt lean manufacturing and visual factory management processes.”

The Factory Vision™ family of full matrix marquees and process control boards provides unprecedented flexibility. This family of robust industrial displays has been developed to meet the needs of a variety of manufacturing applications. Factory Vision™ displays are capable of standard row-column layouts, multiple page full text and graphics, or full motion video replay. From one line marquees to twenty one line process control and andon boards, our products allow your customers to expand into larger applications without reinvesting in training or new software systems.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-10-01

FOR IMMEDIATE RELEASE:

Introducing The new Factory Vision™ Line of Full Color Marquees

and Process Control Boards

Distributed by Ontor Limited. Murrplastik Systems, Inc. is pleased to announce the release of the KDL/E Panel Entry System with improved gasket technology. The KDL/E, while allowing for an enlarged panel knock-out / cut-out, provides three major advantages versus the KDL/N Panel Entry System line of products: Housing design eliminates loose hardware components, up to 20 cables can be configured through one single knock-out. unique latch system provides ease of assembly for varying panel thickness. Other advantages include simple entry of pre-assembled cable connectors; huge time savings due to uninterrupted cable guidance; rapid assembly via the click system, via assembly being almost tool-free, no cumbersome screwing, few parts for simple assembly; simplest strain relief; high degree of protection (IP 54), and high packing density.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Cambridge, Mississauga, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-08-16

FOR IMMEDIATE RELEASE:

Meter Aids in Large Engine Maintenance

Users of large gasoline engines pressurizing pipelines and in regional power generating stations are simplifying maintenance and monitoring programs with a portable meter from Kistler Instrument Corp (Distributed by Ontor Limited). Type 2515A1 engine peak meter with cylinder pressure indicating, calculation and memory provides a new level of portable convenience.

Designed for piezoelectric pressure sensors, data storage for 36 successive pressure cycles is provided. The instrument can store waveforms from 20 locations. Calculations include the arithmetic mean value of the peak pressure, the standard deviation, the steepest slope of the pressure curve as well as the engine speed.

Measuring error is reduced by a 300 Hz Butterworth low pass filter. A readily available 9-volt battery provides a 20 hour service life. An LCD provides easy to view indication with RS-232 interface capability.

Kistler is a worldwide supplier of precision instrumentation for the measurement of pressure, force and acceleration serving the R&D, Industrial and OEM Communities.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-08-01

FOR IMMEDIATE RELEASE:

Tiny Instrumentation Amp Supports

Advanced Process Monitoring

Distributed by Ontor Limited. A new sensor amplifier from Kistler Instrument advances signal conditioning for industrial process monitoring. The type 5030A… MiniAmp series of charge amplifiers is so small, less than 1.5 inches square, and lightweight that it can be mounted strategically close to the sensor, even on moving machinery components. Often the location of the sensor is critical and this amp can be conveniently integrated into machinery, with the wiring dressed out of harm’s way. The single channel amplifier input accepts any piezoelectric sensor operating in high impedance, charge mode. Momentary data events, often lost with strain gage instrumentation, are reproduced exactly due to its wide bandwidth. With two measuring ranges, it can be digitally switched, while in operation.

The rugged enclosure is watertight at protection level IP65 to withstand production floor environments. The digital electronics enable easy integration into industrial control systems for monitoring and process quality improvement.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Waterloo, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-08-01

FOR IMMEDIATE RELEASE:

ONTOR APPOINTED DISTRIBUTOR

FOR EDISON FUSE

Ontor Limited has been appointed distributor for Edison Fuse. With roots reaching back 100 years, Edison Fuse is a leading provider of high-quality overcurrent protection products for North America. They have the resources and technology to develop circuit protection solutions to safeguard electrical systems. Proven Edison Fuse products are found in a broad range of applications throughout commercial and industrial power Distribution systems.
Ontor Limited is among Canada’s leading Industrial Systems Suppliers with a reputation for providing superior service and support. Ontor’s corporate office is located in Toronto with branches across the country in Montreal, Quebec City, Sudbury, Windsor, Waterloo, Burlington, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-08-01

FOR IMMEDIATE RELEASE:

SIRIUS SAFETY RELAYS & CONTACTORS

Distributed by Ontor Limited. Siemens Sirius Safety Contractors and control relays are now available with permanently attached front mounted auxiliary contact blocks. Features include: control relays meet or exceed the requirements specified in the IEC standard for auxiliary devices, 60947-5-1; contactors meet or exceed the requirements specified in the IEC standard for auxiliary devices, 60947-4-1; permanently attached auxiliary contact blocks on the control relays; 3RH12 are available in various combination up to 8 contacts; manual operation of the contactor or control relay prevented.
Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Waterloo, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-07-01

FOR IMMEDIATE RELEASE:

High Precision, Dual Programmable

Analog Inductive Proximity Sensor

Distributed by Ontor Limited. Baumer Electric introduces the new IWRM 12Z8704/S14C analog inductive proximity sensor with independently programmable digital and analog outputs. This completely self-contained unit delivers highly precise non-contact proximity, position and distance sensing for metal objects, and is capable of identifying two different metal substrates in the same application.

The IWRM 12Z8704/S14C sensor features digital output with two selectable trigger points, and may be used for sorting metal objects, concentricity or shape sensing, assessing wear measurement and circularity, and thickness measurement. IP 67 approved, the Dual Programmable Inductive Sensor features an operating range of 0 to 4 mm, and a resolution of 0.005 mm with a deviation of just 0.05V for consistent output. The sensor’s supply voltage range is 10 to 30 VDC and response time is <2.5 ms.

Measuring just 2.5-inches long and 0.5-inch in diameter, this is the smallest output self-contained dual programmable sensor on the market. The sensor features a quick-disconnect connector and a built in amplifier for quick and easy installation and removal. Reversible output allows the end user to match output to any target application without complicated reprogramming of controllers. The sensor also offers an external teach-in mode and a remote programmable set point that allows the controller to reprogram the sensor on the fly.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Waterloo, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-07-01

FOR IMMEDIATE RELEASE:

TYPE CFS – COMPACT FUSIBLE DISCONNECT SWITCHES

Distributed by Ontor Limited - Siemens Type CFS compact fusible switches meeting UL98 requirements and can be used in either service entrance or branch circuit applications. 30-400A, 3 pole switches are offered and all are rated 600V AC maximum. 30A switches are available with provisions for either Class CC or J fuses. 60A and larger switches are provided with Class J fuse provisions and can also be used in non-fusible applications with field installable no-fuse kits. All are open style and are designed to be panel mounted. A variety of door mounted rotary operators are available with Type 1, 3R, 12 or 4/4X ratings. All are UL listed under file number E1211152 and CSA certified under file number 222227.

Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Waterloo, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-04-01

FOR IMMEDIATE RELEASE:

WIRING SIMPLIFIED WITH MOLDING PRESSURE SENSORS

Distributed by Ontor Limited – Single wire technology for larger plastics molds use is now available from Kistler Instrument. Two improved pressure sensors extend the use of single wire conductors that replace coaxial cables. Kistler announced the advance with pressure sensors for small molding applications last year. This wiring mode speeds in-the mold pressure sensor installation and simplifies the dress of wiring. Procedures such as shortening cables and attachment to connectors are accomplished quickly, without the need to solder connections. Push on connectors enable slipping in stripped wires to make connections.
Kistler pressure sensors 6157B, front diameter 4mm, and 6152A, front diameter 6mm, use this single wire technology with wire lengths up to 5m. These sensors are equipped piezoelectric elements and operate in the high impedance, charge mode. Compact sensor amplifiers that often are remotely located, can now be added to the mold or designed into the mold because of this wiring convenience. Once in a production sequence, any wire damage occurring during the molding process is more easily repaired.
Kistler is a worldwide supplier of precision instrumentation for the measurement of pressure, force and acceleration serving the R&D, Industrial and OEM Communities.
Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Waterloo, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-04-01

FOR IMMEDIATE RELEASE:

MODLINK MSDD SOLUTION FOR POWER AND DATA ACCESS

Distributed by Ontor Limited - Murrelektronik, Inc, manufacturer of electronic components and solutions, has launched a new transparent range of front panel interface products with IP65 protection. Featuring transparent, slim profile frames with thousands of modular insert combinations, MODLINK MSDD offers an ideal solution for power and data access without opening the control panel.
“MODLINK MSDD interface modules allow laptops, programming and diagnostic devices, networks or modems to be connected easily without ever opening the control panel,” says Bart Caudell, Murrelektronik’s Technical Engineer. “Unnecessary cabling is therefore omitted and control cabinet components are operated within the appropriate protection category.”
Murrelektronik offers single and dual mounting frames that can be installed with any combination of modular inserts that simply snap into the frame, giving thousands of combination possibilities to suit each customer’s exact needs. The frames have a standard flat profile, which is unique in the market, allowing modules to be fitted closely to the panel and taking up a minimum amount of space. The unique transparent cover with separate lockable lids allows a clear view of signal indicators and data connectors within the cabinet, all while maintaining IP65 protection.
MODLINK MSDD is UL certified and offers EMC shielding for data cables and has high mechanical and.
Ontor is a national distributor of Industrial Automation Systems. The corporate office is located in Toronto with regional offices in Montreal, Quebec City, Burlington, Windsor, Waterloo, Sudbury, Edmonton and Calgary.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-03-01

FOR IMMEDIATE RELEASE:

Internal Combustion Engine Monitoring, Analysis and Control System

Distributed by Ontor Limited - The DII-7P has been developed to monitor reciprocating engine performance by means of electronic sensors. DII-7P helps to spot engine malfunctions at an early stage, yielding benefits in proper Condition Based Maintenance scheduling, emergency avoidance and engine overload protection. Use of the DII-7P system will assure your Power Plant improved reliability and efficiency. Features include:

Continuous Engine protection
System Advice generation for:

Cylinder balancing
Better overall engine performance
Higher fuel efficiency
Lower pollution

Custom setup for Parameter limitations
Remote data access and engine control
Condition Based Maintenance to allow proper Maintenance Scheduling

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-03-01

FOR IMMEDIATE RELEASE:

SIEMENS SIRIUS 3RW SOFTSTARTS

The new Siemens SIRIUS 3RW family of soft starters covers all standard and high-feature motor starting applications. From the smallest softstart in the world at only 22.5mm wide to the most powerfull in the 3RW family at 750 HP, as much as 70% space savings can be realized. With powerful features like programming via built in operator display and keypad, programmable ramp up and ramp down profiles, selectable current limiting, closed loop torque control, integrated motor overload protection and integrated state and fault monitoring is easy to see why the new SIRIUS 3RW is the most flexible, smoothest operating softstart available. Thanks to the integrated bypass contact system, a bypass contactor can be completely eliminated. Of course the high feature 3RW44 can even be connected to PROFIBUS to have it communicate with other equipment and the outside world. Stayed tuned, the SIRIUS 3RW Soft Starters are coming soon.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2005-02-01

FOR IMMEDIATE RELEASE:

Intrinsically Safe Digital Camera Ex-Cam 01

From ECOM Instruments (distributed by Ontor Limited) is the intrinsically safe digital camera Ex-Cam 01 (3.2 Mega Pixel, 4x digital zoom) with its very robust housing and its high IP rating makes it ideal for use in the hazardous (classified) location.
The 2” built in TFT display makes it easy to check for the right picture, shows the resolution and shows also the remaining pictures. The i.s. Ex-Cam 01 has a built in 128MB SD card, which allows even with the highest resolution to take up to 70 pictures. After you have set up the time and day, you can also document the pictures. The data transfer with the desktop PC and the charging of the internal battery happens with a USB docking station outside the hazardous (classified) location.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2004-01-01

FOR IMMEDIATE RELEASE:

Delta's New RMC70 Series Motion Controllers Offer More
Value for One- and Two-Axis Applications

The new RMC70 Series motion controllers from Delta Computer Systems, Inc. and distributed by Ontor Limited offer attractive price/performance for one-axis and two-axis systems.

The initial version to be delivered, the RMC75S-MA1 is oriented toward linear motion control and includes RS232/485 Serial communications and interfaces to these absolute position transducers: MDT (magnetostrictive displacement transducer), and SSI (synchronous serial interface).

The RMC70 Series targets hydraulic, pneumatic and electric servo motion control applications with position, velocity and position/pressure control capabilities. As with Delta's other motion controllers, the RMC70 includes powerful software for easy setup, tuning, programming and diagnostics.

Steve Nylund, Delta,s CEO stated, "The exciting all-new RMC70 product complements Delta,s flagship RMC100 family and expands Delta markets by offering even more value for one and two axis applications."

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2003-12-01

FOR IMMEDIATE RELEASE:

New Process Controller is Operated
By Web Browser

A new process controller designed for network operation in production control systems is announced by Kistler Instrument. The 5863A CoMo Net‰ process controller is a two-channel unit for DIN rail mounting that is operated by a standard web browser via the ethernet on a PC or web terminal. The unit accepts sensor data and can be adjusted to control and monitor a wide variety of production processing operations involving force. Data from piezoelectric sensors in charge or voltage mode and strain gages activate 12 evaluation functions that can be monitored for processes up to 20 cycles per second.

Six SPC-compatible digital inputs and outputs allow the system to be integrated into a machine control systems. Memory for storing the last 10 measured curves for error analysis is provided. Extensive process data compilation with statistical cp and cpk value analyses advance the level of process evaluation. The unit operates on 24V industrial power and is furnished with an integral web server. The 5863A is a part of a process control/monitor series that joins the existing CoMo line intended for retrofitting individual processes.

Kistler is a worldwide supplier of precision instrumentation for the measurement of pressure, force and acceleration serving the R&D, Industrial and OEM Communities.

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2003-12-01

FOR IMMEDIATE RELEASE:

Load Washer Series Has Wide Measuring Range

A series of 8 load washers from Kistler Instrument measure dynamic and quasi-static forces from a few pounds of force to over 269,000. Each sensor has the unique capability to measure extremely small forces throughout any force level within total measuring range.

Precise quartz measuring elements have high rigidity to capture fast moving events.

Many mounting accessories enable high adaptability to a number of applications in production and metal processing. These force sensors are designed to use with charge amplifiers and process control monitors where the load washer captures parameter data that in turn with a controller, maintain assembly forces in tight tolerances, to eliminate variances that can lower yield.

Kistler is a worldwide supplier of precision instrumentation for the measurement of pressure, force and acceleration serving the R&D, Industrial and OEM Communities.

K2.9001 10/03

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2003-10-01

FOR IMMEDIATE RELEASE:

IP Security and SNMP Functions Available for Linux IPm Controllers and RTUs

New IP Security Protection and SNMP "add-on" features are available for use with SIXNET's VersaTRAK IPm Remote Terminal Unit (RTU), SixTRAK IPm Open DCS Controller, SixTRAK I/O Controller (OEM Linux model), and the new EtherTRAK Dual Ethernet Gateway.

The IP Security add-on feature is a firewall application which allows users to protect their controller/RTU from unauthorized access. A simple Security Rules Wizard in SIXNET's I/O Tool Kit is used to define rules that restrict access (incoming or outgoing) based upon IP address, IP ports, or any other capability of the IPtables Linux application which comes installed on IPm units as part of their standard firmware.

The SNMP add-on provides users with the ability to obtain valuable network management information from the SNMP agent (Simple Network Management Protocol) in their IPm controllers or RTUs. A Rules Wizard in the I/O Tool Kit configures the SNMP agent that has been integrated into the standard IPm firmware.

Puchase of a license is required to use either of these new add-on features with IPm units. Licenses may be obtained directly through SIXNET's Web Store at www.sixnetio.com. Once the license for the add-on has been purchased, users simply "unlock" the new capability using their I/O Tool Kit so they can make immediate use of the enhanced functionality. The latest version of SIXNET's I/O Tool Kit (v2.2) and IPm Firmware (v1.5+) are required, and are available at no charge through SIXNET's web site (where they can either be downloaded directly or requested on a free CD).

Distributed by ONTOR LIMITED

12 Leswyn Road
Toronto, Ontario
Canada M6A 1K3
Phone: (416) 781-5286
Fax: (416) 781-7680
For more information contact Cameo Gill
2003-01-01

FOR IMMEDIATE RELEASE:

New Low Cost RemoteTRAK¨ RTU /
Combination I/O Module

The new RemoteTRAK¨ RTU / Combination I/O module (model RM-RTU-8440-F) combines a mix of I/O types (8 discrete inputs, 4 discrete outputs, 4 analog inputs) with a RS232/RS485 interface.

The RemoteTRAK¨ RTU is designed as an economical I/O solution for situations where you need: a low cost RTU at a remote site; poll I/O or Modbus devices on a RS485 party line; or expand the number of channels on a SIXNET EtherTRAK node.

The RemoteTRAK¨ RTU supports Modbus ASCII, RTU, and the SIXNET protocol. It also supports radio packeting and phone links. This enables users to poll the RemoteTRAK¨ RTU with an industrial modem (such as SIXNET's VT-MODEM) or radio using SIXNET or Modbus protocol.

All SIXNET I/O is engineered to withstand the abuse of harsh industrial environments. The RM-RTU-8440-F is surge and vibration resistant, operates in temperatures ranging from -40 to +70¡C, and is CE, UL, CSA, and Class 1, Division 2 (Zone 2) rated. The module also has Det Norske Veritas (DNV) No. 2.4 (Class A & B) certification for marine and offshore use. It is encased in rugged Lexan for added durability.